Skip to main content
Lit board-formed concrete retaining wall and steps on a hillside
Design · Permit · Build

Paver & Hardscape Contractor in Studio City

Paver patios, driveways and walls, built on a proper base by our own crews.

Licensed contractor
California general contractor, CSLB #1119054. Bonded and insured.
Typical cost
Paver patio and hardscape: from about $13,000.
Permits
Issued by LADBS. We handle the plans and the submittal.

Built for Studio City Homes

Studio City sits about ten minutes from our Cahuenga Pass base, and it is two markets in one. Cross Ventura Boulevard heading north and you are on flat, deep lots where a pool, an outdoor kitchen and a lawn all fit comfortably in a single phase.

Head south into the canyons and the same budget buys a very different project, because retaining and access come first and the pool follows.

A split market: flat valley-floor lots north of Ventura Boulevard (the single-family median is about 7,000 square feet in LA County Assessor data) and hillside parcels to the south, which are often larger but steep. The two build very differently and price very differently.

What to Plan For

Pavers last when the base is right. What you see is the top two or three inches. Underneath is excavation to the correct depth, a compacted base, a setting bed and an edge restraint that stops the field from spreading. That work is where a paver job is won or lost, and it is the part a low bid leaves out.

Water comes next. Hardscape changes where rain goes, so we set the slopes and add drains while the ground is open. Fixing drainage after the pavers are down means lifting them again.

The material is your choice. Concrete pavers, porcelain and natural stone such as travertine differ in look, in how hot they get underfoot and in price. A driveway needs a thicker paver and a deeper base than a patio. We bring samples and show the layout in 3D, so the pattern and the borders are settled before we order.

We are a design-build team, which means the people who draw your project are the people who build it. Design, engineering, permits and construction run through one project manager and our own crews, so nothing gets lost in a handoff between a salesperson and a subcontractor. We are licensed, bonded and insured, CSLB license #1119054.

Permits in Studio City: Private pools in the City of Los Angeles are permitted through a Combined Building-Mechanical permit, while pools serving more than two dwelling units need separate building, electrical, plumbing and mechanical permits. Using a City of Los Angeles standard plan on file with LADBS reduces plan check time.

Most properties south of Ventura Boulevard, in the hills, are inside the Hillside Grading Area. A pool there needs its own LADBS grading permit, and the Baseline Hillside Ordinance caps grading and import/export quantities. Much of that hillside is also a Very High Fire Hazard Severity Zone.

Permit details checked September 2026 against LADBS. Rules change, so we confirm them again for your parcel.

What We Build

  • Retaining walls and slope stabilization
  • Canyon-access excavation and haul-off planning
  • Paver patios and pool decks
  • Paver driveways and walkways
  • Concrete, porcelain and natural stone pavers
  • Excavation, compacted base and edge restraint
  • Drainage correction and grading
  • Retaining walls and seat walls
  • Steps, landings and planters
  • Fire pits with built-in seating
  • Artificial turf and turf joints
  • Low-voltage hardscape lighting

Local Conditions

What to Know in Studio City

These local conditions change the scope, the schedule and the budget.

01

Hillside lots south of Ventura Boulevard often need engineered retaining and caisson work before any pool shell is poured

02

Narrow canyon streets limit equipment access, which drives staging and haul-off planning

03

Flat valley-floor lots north of Ventura Boulevard are far simpler and usually build faster

Areas we serve in Studio City:Silver TriangleFryman Canyon

Investment

What It Costs in Studio City

Real Southern California price ranges, not teaser numbers.

Paver patio and hardscape

from about $13,000

What moves it: square footage, paver type, base preparation, drainage, and any steps or retaining involved

Retaining walls

$60 to $150 per face foot

What moves it: height, whether the wall is engineered, material choice, drainage behind the wall, and access for equipment and materials

Artificial turf

from about $9,900

What moves it: area, turf grade, base depth, drainage, and any pet-specific infill

Your lot, access and finishes set the price. We walk the site, then show you where every dollar goes.

Get a line-item price for your Studio City property

The Process

How We Work in Studio City

01

Site Review

We measure the area, check soil, slope and drainage, and note access for equipment and materials.

02

Design & 3D

You see the layout, pattern, borders and material in 3D before anything is ordered.

03

Plans & Permits

Walls, driveway approaches and drainage work are drawn and permitted where your city requires it. In Studio City that submittal goes to Los Angeles Department of Building and Safety (LADBS).

04

Demo & Excavation

Old concrete comes out and the area is dug to the depth the new base needs.

05

Base & Pavers

Base is placed and compacted in layers, then the setting bed, pavers, cuts and edge restraint.

06

Joints & Handover

Joints are filled and compacted, the surface is cleaned, and we walk the finished work with you.

Questions

What Studio City Homeowners Ask

Who issues the permits for this work in Studio City?

Los Angeles Department of Building and Safety (LADBS). Private pools in the City of Los Angeles are permitted through a Combined Building-Mechanical permit, while pools serving more than two dwelling units need separate building, electrical, plumbing and mechanical permits.

Using a City of Los Angeles standard plan on file with LADBS reduces plan check time. Most properties south of Ventura Boulevard, in the hills, are inside the Hillside Grading Area. A pool there needs its own LADBS grading permit, and the Baseline Hillside Ordinance caps grading and import/export quantities.

Much of that hillside is also a Very High Fire Hazard Severity Zone. We prepare the drawings, make the submittal and handle plan-check corrections ourselves, so you are not the one chasing plan check.

What makes building in Studio City different?

A split market: flat valley-floor lots north of Ventura Boulevard (the single-family median is about 7,000 square feet in LA County Assessor data) and hillside parcels to the south, which are often larger but steep. The two build very differently and price very differently.

One local condition that shapes the work: Hillside lots south of Ventura Boulevard often need engineered retaining and caisson work before any pool shell is poured.

Which parts of Studio City do you work in?

All of it, including Silver Triangle and Fryman Canyon. Our crews run every job out of our Cahuenga Pass base in Los Angeles, with our own people on site.

What does a paver or hardscape project cost in Studio City?

Paver patio and hardscape: generally from about $13,000 across Southern California. What moves it is square footage, paver type, base preparation, drainage, and any steps or retaining involved. We give line-item pricing after seeing the site rather than quoting a number over the phone.

How long does a paver project take?

Most paver patios and walkways take three to six weeks of construction. Driveways, retaining walls and drainage work add time, and so does demolition of thick existing concrete.

Do pavers need a permit?

A patio on grade usually does not. Retaining walls above a certain height, a driveway approach at the street and work that changes drainage often do, and the thresholds differ by city. We check with your building department before we price the job.

Can you pave over my existing concrete?

Sometimes, with thin pavers made for overlays, if the slab is sound and the added height works at doors and steps. A cracked or sinking slab should come out, because the pavers will follow whatever is under them.

How do I look after pavers?

Very little is needed. Sweep them, rinse them, and top up the joint sand if it washes out over the years. If one paver stains or settles it can be lifted and reset, which is the main advantage over poured concrete.

Planning Pavers in Studio City?

Sit down with your project manager and get an accurate estimate. We call you back within one business day.

Licensed, bonded & insured · CSLB license #1119054